Once complete you will need to attach the pole using U clamps which you have received with the package. Now connect your motor with U Clamp which is connected with pol. You can remove your antenna from the current installation and fit it as showing below picture. Make sure the mounting tube indicates 0 degrees, otherwise driver the mounting tube 2 to exact 0 degrees via the manual buttons on the bottom of the mount make sure you have connected the motor with the receiver that is switched on.
Make sure the mounting pole is exactly vertical before the installation of the motor. Fix the H-H Mount onto the mounting pole of the stand and tighten the two U-Screws 4 by the clamp 6 and nut 5 evenly.
Make sure there is no obstacle in the southern sky, such as a tree or building. Aiming True South — Attaching the antenna dish to the mount, make sure it is at the center of the mounting tube. Set the Declination Angle by the scale on the Antenna dish. Drive the antenna east and west via the manual buttons on the bottom of the Mount to check if the reception arc is correct.
Please note: In order to have the power to drive the antenna, please connect the mount to the receiver or interface box via coaxial cable first. The commands of the receiver might be different, but similar, Please refer to the manual of the DiSEqC 1. Store nn: Store satellites position nn 4. Goto nn: Drive Motor to satellite position nn 5. The original position will be shifted to a new position. All the other Satellite positions are also changed.
When the values have been correctly received, the receiver drives the Motor to the calculated position. Slightly rotate clockwise or anticlockwise the antenna and the Motor locked together until you find an image on the TV screen connected to the receiver or the signal on the strength field meter, and then tighten the fixing screws. Cut off the power by unconnected Coaxial cable. Connect Coaxial cable 4. Cut off the power by unconnected Coaxial cable 2. Click on a star to rate it! Average rating 4.
In my other illustration, we will be using a decoder with numbers. For this guide, we are using DiSEqC version 1. Also, you will notice that your dish signal quality is zero if your DiSEqC is off. This is shown in the picture below:. Here is my second illustration which covers a wider range of decoders. At times, a previously working DiSEqc switch may just start malfunctioning all of a sudden. In this section, I will teach you some troubleshooting guides with DiSEqC as well as the solutions to problems encountered during or after installing a DiSEqC switch for your decoder.
And what settings do you have in your receiver? Irrespective of the problems you are encountering with your DiSEqC Switch, my solutions below will surely fix the issue. There are to categories of DiSEqC switch problems. The first one occurs during installation while the second problem will arise long after a successful installation. This section will take care of both issues.
If you are not getting the desired result when installing your DiSEqC switch, try and follow the troubleshooting guides below to fix the same. I mean in the event that your perfectly working DiSEqC switch just started giving problems, here are the steps you need to take in order to solve the problems. Once you are certain that none of the tips above could correct the situation, it is time to do advanced troubleshooting.
It is likely either your switch or the LNB or the decoder is faulty. Totally disconnect the switch and connect your cable directly to the decoder. If you get signal and your channels open normally. To isolate this fault, you need to change your LNBf. Also, try and get your decoder closer to the LNB so as to ensure that the distance between the two is not interfering with the signal quality.
How can i watch all the channels without change disegc I mean if i am on channels A without change to B. Please, I have a really big challenge with my 8 in 1 diseqc Switch. My first four satellites are set to Diseqc 1. Those ones are functioning normally. But I am not able to access my 5th LNB. I set it to Diseqc 1. I do not understand where I went wrong. I need your guide on how to make my decoder see this 5th LNB Satellite please.
Thanks,l need frequency, symbol rate and polarization to trap free to air channels on Ds TV in Ghana. I use my dish with multifees with 2 lnbs and a diseqc switch.
My satfinder has found the satellites and they are working. I found a diseqc setup image from digiwave. Then each 1 to 4 diseqc to a receiver. But nothing works. No signal at all. Dafini: try and connect the individual LNBs directly to the decoder. To properly troubleshoot this, get another fta decoder and use it to test your dish and disceqc. Alternatively, borrow any diseqc that has been confirmed to be working and install it.
Am agbeko from ghana and I just started satellite work, pls I want to know how can you get more FTA terrestrial channels and which outdoor digital tv antenna do I need? Good morning sir, I have problem with diseqc setting on Korean strongest decoder stga, I am setting up two dishes with same satellite on 28e with different TP multi tv on 28e v and Arewa24 on 28e v Master , please what is the best way one can do with one disc but two or more lnbf more satellites.
Paul: If you already know that the satellite do not cover your region, it is time to look for one that is receivable in your region sir. Hi Lemmy this is Kaduyu from Uganda plz help me I need to connect A Hisense TV inbuilt decorder with two dishes one of it is sharing with an Azam decorder and the other is going direct to the TV receiver The problem is when I connect the two dishes on the TV it loses the signal plz help.
However, your decoder had detected your lnb. Please determine the satellite position you want to face and track it accordingly. Better still, call your local satellite installer. Pls oga leeme am using qsat 23G and i set my dish to dstv and joy tv,bt my acct has expired since last yr,so can i buy it? Hi Lemmy, my srt a did not stream youtube with with my 3G modem and the patch. Can cccam work in the srt a using a 3G modem? Hi Lemmy. I blind scan on Amos I lost all the channel on V , a lots channel.
Please help me. Mr lemmy pls how can i track multi tv and amos 17 e with one size 90cm dish pls i need your reply with diagram pls. I have Speed HD s1 my some how it was reset to factory setting and i am using 2 dish DSTV and Multi TV, I have tried to scan for multitv and yet i only get DSTV, maybe i have the wrong frequency or the upgrade did not not, can you help with the frequency i should use please i need some more free active channel as network has been problem connecting to DStv channels.
However help me out with this. Hi Lemmy pls I downloaded Azsky recharge tool V3. Thanks Lemmy for this. It helps me make working some channel that was showing bad signal. However remains some issues. On the same satellite some work on port B whereas some on port D in my case.
Some shows service not available on another satellite whereas some bad signal on other satellite whatever the port. You know on Eutelsat36A36 Kennis music, mm24 quest and other on V Shows service not available even though the signal are good. So am wondering what to do to see those channel. Any bit of help are welcome. Williams, kennis music is on Amos Thanks in advance!
0コメント